TIMKEN H414235-H414210-B tapered bearings with Flange
Also known as : H414235-H414210-B
- Inside Diameter: 63.5 mm
- Outside Diameter: 136.525 mm
- Width: 16.637 mm
- Basic dynamic load rating: 323 kN
- Basic static load rating: 335 kN
TIMKEN H414235-H414210-B Bearing
TIMKEN H414235-H414210-B Bearing details
| Series | H414200 |
|---|---|
| model | H414235-H414210-B |
| Cone Part Number | H414235 |
| Cup Part Number | H414210-B |
| Design Units | Imperial |
| Cage Type | Stamped Steel |
| Bearing Weight |
2.900 Kg 6.50 lb |
| Dimensions | |
| d - Bore |
63.500 mm 2.5000 in |
| D - Cup Outer Diameter |
136.525 mm 5.3750 in |
| D1 - Flange Outer Diameter |
143.637 mm 5.6550 in |
| B - Cone Width |
41.275 mm 1.6250 in |
| C - Cup Width |
31.750 mm 1.2500 in |
| C1 - Cup Flange Width |
7.112 mm 0.2800 in |
| T - Bearing Width to Flange |
16.637 mm 0.6550 in |
| T1 - Bearing Width |
41.275 mm 1.6250 in |
| Abutment and Fillet Dimensions | |
| R - Cone Backface "To Clear" Radius |
3.600 mm 0.14 in |
| r - Cup Backface "To Clear" Radius |
3.30 mm 0.130 in |
| da - Cone Frontface Backing Diameter |
78 mm 3.07 in |
| db - Cone Backface Backing Diameter |
82 mm 3.23 in |
| Da - Cup Frontface Backing Diameter |
130.05 mm 5.16 in |
| Ab - Cage-Cone Frontface Clearance |
3.6 mm 0.14 in |
| Aa - Cage-Cone Backface Clearance |
3.3 mm 0.13 in |
| a - Effective Center Location |
-10.9 mm -0.43 in |
| Basic Load Ratings | |
| C90 - Dynamic Radial Rating (90 million revolutions) |
83700 N 18800 lbf |
| C1 - Dynamic Radial Rating (1 million revolutions) |
323000 N 72600 lbf |
| C0 - Static Radial Rating |
335000 N 75400 lbf |
| Ca90 - Dynamic Thrust Rating (90 million revolutions) |
51600 N 11600 lbf |
| Factors | |
| K - Factor | 1.62 |
| e - ISO Factor | 0.36 |
| Y - ISO Factor | 1.67 |
| G1 - Heat Generation Factor (Roller-Raceway) | 113 |
| G2 - Heat Generation Factor (Rib-Roller End) | 22.8 |
| Cg - Geometry Factor | 0.0827 |
As TIMKEN bearing distributor, Nodes bearings have TIMKEN H414235-H414210-B bearings in stock, TSF (Tapered Single with Flange) Imperial , Tapered roller bearings.
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
