The main dimensions of the FAG spindle bearings conform to DIN 628-1. The dimensional tolerances of the bearings correspond to tolerance class P4, the running tolerances correspond to tolerance class P2 to DIN 620-2.
The actual value codes for the bore and outside diameter as well as the nominal value deviation for the bearing width are indicated on the end faces of the inner and outer rings as well as on the packaging, where they are stated in the sequence “bore/outside diameter/bearing width”.
Inner ring tolerance
Bore | Bore deviation | Width deviation | Width variation | Radial runout | Axial runout | ||||
---|---|---|---|---|---|---|---|---|---|
d mm |
Δdmp μm |
ΔBs μm |
VBs μm |
Kia μm |
Sd μm |
Sia μm |
|||
over | incl. | ||||||||
- | 10 | 0 | –4 | 0 | –100 | 1,5 | 1,5 | 1,5 | 1,5 |
10 | 18 | 0 | –4 | 0 | –100 | 1,5 | 1,5 | 1,5 | 1,5 |
18 | 30 | 0 | –5 | 0 | –120 | 1,5 | 2,5 | 1,5 | 2,5 |
30 | 50 | 0 | –6 | 0 | –120 | 1,5 | 2,5 | 1,5 | 2,5 |
50 | 80 | 0 | –7 | 0 | –150 | 1,5 | 2,5 | 1,5 | 2,5 |
80 | 120 | 0 | –8 | 0 | –200 | 2,5 | 2,5 | 2,5 | 2,5 |
120 | 150 | 0 | –10 | 0 | –250 | 2,5 | 2,5 | 2,5 | 2,5 |
150 | 180 | 0 | –10 | 0 | –250 | 4 | 3 | 4 | 5 |
180 | 250 | 0 | –12 | 0 | –300 | 5 | 4 | 5 | 5 |
Outer ring tolerance
Outside diameter | Outside diameter deviation | Width variation | Radial runout | Axial runout | |||
---|---|---|---|---|---|---|---|
D mm |
ΔDmp μm |
VCs μm |
Kea μm |
SD μm |
Sea μm |
||
over | incl. | ||||||
18 | 30 | 0 | –5 | 1,5 | 2,5 | 1,5 | 2,5 |
30 | 50 | 0 | –6 | 1,5 | 2,5 | 1,5 | 2,5 |
50 | 80 | 0 | –7 | 1,5 | 3 | 1,5 | 4 |
80 | 120 | 0 | –8 | 2,5 | 4 | 2,5 | 5 |
120 | 150 | 0 | –9 | 2,5 | 4 | 2,5 | 5 |
150 | 180 | 0 | –10 | 2,5 | 5 | 2,5 | 5 |
180 | 250 | 0 | –11 | 4 | 7 | 4 | 7 |
250 | 315 | 0 | –13 | 5 | 7 | 5 | 7 |
315 | 400 | 0 | –15 | 7 | 8 | 7 | 8 |
The width deviation ΔCs is identical to ΔBs of the corresponding inner ring.